Arduino tastatura sa specijalnim tasterima - navigaciona. Kakakterstike: - Tasteri: AUTO, MENU, LEFT, RIGHT i POWER - LED dioda indikaciona - Veličina: 115 x 22.4 x 0,8 mm - Dužina kabla: 100 mm (uključujući konektor) - Konektor: 7 pinova, 0,1``(2.54mm raster) - Maksimalan napon: 35 V DC - Maksimalna sruja: 100 mA - Dielektrična otpornost: 250 VRms (60Hz, 1min) - Upotreba: 1.000.000 uključenja

Arduino tastatura sa specijalnim tasterima - navigaciona. Kakakterstike: - Tasteri: AUTO, MENU, LEFT, RIGHT, SELECT i ON/OFF - LED dioda indikaciona - Veličina: 103 x 24 x 0,8 mm - Dužina kabla: 105 mm (uključujući konektor) - Konektor: 9 pinova, 0,1``(2.54mm raster) - Maksimalan napon: 35 V DC - Maksimalna sruja: 100 mA - Dielektrična otpornost: 250 VRms (60Hz, 1min) - Upotreba: 1.000.000 uključenja

HERZ - Termostatske glave sa priključkom M 28 x 1,5, model 7260, nekorišćena u kutiji, opis sa net-a : `-Termostatska glava STANDARD punjena termouljem za HERZ termostatske ventile. - Pričvrsna navrtka M28 x 1,5 mm je od mesinga, niklovana. - Sa ograničenjem i blokadom nameštene vrednosti, bez mehaničkog zatvaranja. - Opseg podešavanja 6 - 28 °C. - Zaštita od smrzavanja na 6 °C. - Oznake nameštanja temperature na termostatskoj glavi: 1 – 6`, stanje kao na slikama ... Lično preuzimanje : KOD MENE KUĆI u BG na Senjaku ! Slanje : Post Express-om o trošku kupca ! ***** Pogledajte i ostalu moju prodaju na Kupindu, možda nađete nešto interesantno : http://www.kupindo.com/Clan/nin2/SpisakPredmeta

Merač protoka vode sa senzorom u kompletu i 12V izlazom za rele Uređaj poseduje mod u kome pokazuje u gornjem desnom uglu broj litara koji su prošli kroz senzor, a u centralnom delu trenutnu brzinu protoka. Uređaj se startuje na taster RUN i daje napon na izlazu za elektromagnetni rele od 12V ako se isti koristi i pali merenje protoka i broja litara koji su protekli. Poseduje i programiran mod da na određenoj litraži ugasi napon ventilu i prekine dotok vode, to se postiže u ugašenome stanju na taster STOP i onda na taster SET podešava željena količina vode koja treba da protekne. Na tasteru MENU se bira stavka TOTAL koja pokazuje ukupnu količinu vode koja je protekla kroz uređaj. Karakteristike: - Model: ZJ-LCD-M - Maksimalno merenje: 0,00 do 999.999 L - Maksimalan protok: 9999,99 L/min - Napon napajanja: 12-24 V DC - Napon na izlazu za ventil: DC12V / 0.3-0.5A (NC) - Dimenzije: 103 x 77 x 35 mm - U kompletu i protokomer 1/2 cola i 1-30 litara/min Povezivanje: - Džek sa 2 žice: pozitivan napon napajanja (crvena) i masa (crna) - Džek sa 3 žice: protokomer - Žute žice: izlaz za elektromagnetni ventil Uređaj može da radi i sa drugim protokomerom samo mu treba promeniti broj impulsa za taj protokomer koji daje po litru vode, u našem slučaju je to 7,5. Na taster MENU se dolazi do polja gde je u gornjem desnom uglu pasword (PW), nakon dugog pritiska na SET se ulazi u unos istoga koji je fabrički 1234 i nakon unosa se ulazi u promenu parametra protokomera i isti nakon unosa na MENU pamti.

P08 Izlaz je preko releja direktno spojen sa ulazom,tako da je preporučivo prvo spojiti potrošać pa tek onda napajanje!!! W3002 Digital Temperature Controller 10A Thermostat Control Switch with Probe Sensor Specifications: Product model: W3002 Temperature range: -50 ° C ~ 110 ° C Temperature control range: -50 ° C ~ 110 ° C Temperature measurement accuracy: ±0.2 °C Temperature control accuracy: ±0.1 °C Input voltage: 110-230VAC Output power: 1500W Output type: direct output Mounting hole distance: 73mm (aperture 4mm) Appearance size: 60 x 45 x 31mm Function Setting range: P0 Starting temperature:-50℃~110℃ P1 Stop temperature:-50℃~110℃ P2 Temperature correction:-10℃~10℃ P3 Delayed start:0~10min Introduction to code and features: P0 sets the startup temperature Press the SET button to enter the internal menu. The default display is P0. Press the SET button again to set the desired start temperature with the up and down buttons. P1 sets the stop temperature Press the SET button to enter the internal menu. The display is P0. Press the up and down button to change to P1. Press the SET button again to set the desired stop temperature. P2 set temperature correction In the same way, enter the internal menu, change to P2 by pressing the up and down buttons, press the setting button again, and set the required calibration temperature by the up and down buttons (detection temperature + correction temperature = actual temperature) P3 set delay start In the same way, enter the internal menu, change to P3 by pressing the up and down buttons, press the setting button again, and set the required delay time by the up and down buttons, the unit is minute. (Note: Delay start is generally used for compressor refrigeration. If English refrigerator freezer, this value needs to be set. According to compressor back pressure, it is generally set for 3-6 minutes. If it is not used to control compressor refrigeration, it does not need to be extended. Time function, skip directly.) Heating mode: starting temperatureCooling mode: starting temperature > stop temperature (program automatically determines cooling mode) Common fault code Code Problem Solution 888:Resetting Waiting for normal display LLL:Sensor open circuit Repair or replace the sensor HHH:sensor short circuit

P08 W3002 Digital Temperature Controller 10A Thermostat Control Switch with Probe Sensor Specifications: Product model: W3002 Temperature range: -50 ° C ~ 110 ° C Temperature control range: -50 ° C ~ 110 ° C Temperature measurement accuracy: ±0.2 °C Temperature control accuracy: ±0.1 °C Input power: DC12V Output power: 120W (12V 10A) Output type: direct output Relay on:Blue LED Mounting hole distance: 73mm (aperture 4mm) Appearance size: 60 x 45 x 31mm Function Setting range: P0 Starting temperature:-50℃~110℃ P1 Stop temperature:-50℃~110℃ P2 Temperature correction:-10℃~10℃ P3 Delayed start:0~10min Introduction to code and features: P0 sets the startup temperature Press the SET button to enter the internal menu. The default display is P0. Press the SET button again to set the desired start temperature with the up and down buttons. P1 sets the stop temperature Press the SET button to enter the internal menu. The display is P0. Press the up and down button to change to P1. Press the SET button again to set the desired stop temperature. P2 set temperature correction In the same way, enter the internal menu, change to P2 by pressing the up and down buttons, press the setting button again, and set the required calibration temperature by the up and down buttons (detection temperature + correction temperature = actual temperature) P3 set delay start In the same way, enter the internal menu, change to P3 by pressing the up and down buttons, press the setting button again, and set the required delay time by the up and down buttons, the unit is minute. (Note: Delay start is generally used for compressor refrigeration. If English refrigerator freezer, this value needs to be set. According to compressor back pressure, it is generally set for 3-6 minutes. If it is not used to control compressor refrigeration, it does not need to be extended. Time function, skip directly.) Heating mode: starting temperatureCooling mode: starting temperature > stop temperature (program automatically determines cooling mode) Common fault code Code Problem Solution 888:Resetting Waiting for normal display LLL:Sensor open circuit Repair or replace the sensor HHH:sensor short circuit

P08 W3002 Digital Temperature Controller 10A Thermostat Control Switch with Probe Sensor Specifications: Product model: W3002 Temperature range: -50 ° C ~ 110 ° C Temperature control range: -50 ° C ~ 110 ° C Temperature measurement accuracy: ±0.2 °C Temperature control accuracy: ±0.1 °C Input power: DC24V Output power: 240W (24V 10A) Output type: direct output Relay on:blue LED Mounting hole distance: 73mm (aperture 4mm) Appearance size: 60 x 45 x 31mm Function Setting range: P0 Starting temperature:-50℃~110℃ P1 Stop temperature:-50℃~110℃ P2 Temperature correction:-10℃~10℃ P3 Delayed start:0~10min Introduction to code and features: P0 sets the startup temperature Press the SET button to enter the internal menu. The default display is P0. Press the SET button again to set the desired start temperature with the up and down buttons. P1 sets the stop temperature Press the SET button to enter the internal menu. The display is P0. Press the up and down button to change to P1. Press the SET button again to set the desired stop temperature. P2 set temperature correction In the same way, enter the internal menu, change to P2 by pressing the up and down buttons, press the setting button again, and set the required calibration temperature by the up and down buttons (detection temperature + correction temperature = actual temperature) P3 set delay start In the same way, enter the internal menu, change to P3 by pressing the up and down buttons, press the setting button again, and set the required delay time by the up and down buttons, the unit is minute. (Note: Delay start is generally used for compressor refrigeration. If English refrigerator freezer, this value needs to be set. According to compressor back pressure, it is generally set for 3-6 minutes. If it is not used to control compressor refrigeration, it does not need to be extended. Time function, skip directly.) Heating mode: starting temperatureCooling mode: starting temperature > stop temperature (program automatically determines cooling mode) Common fault code Code Problem Solution 888:Resetting Waiting for normal display LLL:Sensor open circuit Repair or replace the sensor HHH:sensor short circuit

Cene nalepnica su: - 20x 15 cm = 150 din - 30 x 20 cm = 300 din - 50 x 30 cm = 750 din Cene tabli su: - 20x 15 cm = 350 din - 30 x 20 cm = 700 din - 50 x 30 cm = 1500 din Nalepnice su vodootporne, digitalna štampa na PVC foliji, stampa se posebnom tehnikom, tzv. solventna štampa, takve nalepnice se koriste za ispisivanje izloga, vozila, svih vrsta reklama, znači apsolutno su otporne na sve atmosferske uticaje. U slucaju tabli, nalepnica je nalepljena na pocinkovan lim debljine 0,5 mm, koji je nerđajuci. U uglovima su izbušene 4 rupe. -----BESPLATNA DOSTAVA----- BESPLATNA DOSTAVA na teritoriju cele Srbije, ako kod mene kupite proizvode u iznosu većem od 1000 din ! ! ! BESPLATNA DOSTAVA se vrši isključivo s Postexpressom, ja kada šaljem plaćam troškove poštarine, ako mi uplatite novac pre slanja na moj račun u Komercijalnoj banci inemate nikakve troskove. Ako plaćate kuriru Postexpressa kada vam donese, imate troškove povrata novca oko 80 dinara. Broj mog računa je 205-9001018405724-72 Komercijalna banka, ako iz Komercijalne banke uplaćujete novac na moj račun, nemate nikakve troškove, iz Pošte ako uplaćujete troškovi uplate su 45 din, ako uplaćujete Postnet-om na moj mobilni, oko 70 din su troškovi.

P17 Product Description Working voltage: DC12V (normal operating voltage DC10V-16V) Source: DC4V ~ 20V (positive trigger common power button, PNP sensors, PLC signals, etc.) Output capability: You can control the DC or AC 220v5A within 30v5A within Quiescent Current: 20mA, working current: 50mA Life: more than 10 million times; Working temperature: -40 ~ 85'C; Weight: about 26g Dimensions: 64.2mm * 34.8mm * 18.5mm Features: anti-reverse voltage input circuit, worry-free wiring. Signal input optocoupler isolation, anti-interference ability. Set the parameters of power and permanent memory. Powerful flash MCU online programming capabilities, according to user needs can contact the manufacturers to customize the functionality. Modules and devices are powered wiring diagram: power supply modules and devices sharing wiring diagram: Features: S1: power on, press S1 2 seconds to enter mode selection menu, press S1, choose P-1 ~ P-4 mode. S2: OK / Shift key: Press to adjust the position of the LED is blinking, which LED is blinking, S3 to adjust the value of digital tube flicker. Until you press S2, the digital is no longer flashing. S3: digital display flashes, S3 adjustment digits from 0-9 successively changed. Normal digital tube display, S3 to adjust the position of the decimal point, the decimal point in bits 0-999 minutes; in 10 bit from 0 to 99.9 seconds; no decimal point indicates 0-999 seconds. Model Description: P-1: triggering signal is received, the relay is turned on, the timer expires, the relay off. A1: During the delay trigger again invalid A2: During re-timing delay trigger again A3: Delay trigger again during termination timing relay reset P-2: triggering signal is received, X start time, the end of counting relay, Y start time, the end of counting the relay off P-3: Cycle Switch Mode A1: After power relay is turned on, the end of the timing off, an infinite loop. A2: After power relay is off, the timing turned end, an infinite loop. Instructions: P-1 mode: Long press S1 2 seconds to enter mode selection menu, press S1, select P-1, press S2 OK; automatically jump to the menu to select the function after pressing S1 (A1 A2 A3 optional), press S2 OK; automatically jump to set the time, press S3 to adjust the position of the decimal point, automatically jump press S2 OK LED is blinking, press S3 to adjust the flashing digits from 0-9 successively changed, press S2 to determine the order of operation until the blinking stops, set fixed end. P-2 mode: Long press S1 2 seconds to enter mode selection menu, press S1, select P-2, press S2 OK; automatically jump to the [closing time] settings, press S3 to adjust the position of the decimal point, automatically jump press S2 OK turn LED is blinking, press S3 to adjust the flashing digits from 0-9 successively changed, press S2 to determine the order of operation until the flashing stops, the green light; the time to jump to the [open] setting, press S3 to adjust the position of the decimal point, press S2 OK after automatically jump, LED is blinking, press S3 to adjust the flashing digits from 0-9 successively changed, press S2 to determine the order of operation until the flashing stops, setting the end. P-3 mode: Long press S1 2 seconds to enter mode selection menu, press S1, select P-3, press S2 OK; automatically jump to the menu to select the function after pressing S1 (A1 A2 optional), press OK S2 ; automatically jump to the [closing time] settings, press S3 to adjust the position of the decimal point, automatically jump press S2 OK LED is blinking, press S3 to adjust the flashing digits from 0-9 successively changed, press S2 to determine the order of operations until the blinking stops , green light; the time to jump to the [open] setting, press S3 to adjust the position of the decimal point, automatically jump press S2 OK LED is blinking, press S3 to adjust the flashing digits from 0-9 successively changed, press S2 to determine the order of operations until the flashing stops, setting the end. P-4 mode: Long press S1 2 seconds to enter mode selection menu, press S1, select P-4, press S2 OK; automatically jump to set the time, press S3 to adjust the position of the decimal point, and press S2 automatically jump OK, Digital flashes, press S3 to adjust the flashing digits from 0-9 successively changed, press S2 to determine the order of operation until the flashing stops, setting the end.

Regulator brzine obrtanja jedofaznoga motora (AC) sa 5 žica (3 žice za namotaje primara i sekundara motora i 2 žice koje idu sa tahogeneratorskog namotaja motora na ovaj regulator), ON/OFF prekidačem i mogućnošću promene smera obrtanja. Reguliše se potenciometrom od nulte do maksimalne brzine i na tasterima menjaju parametri rada i modovi, a sa zadnje strane ima i konektore za eksterne ulaze tipa krajnjih prekidača. Pogodno za pakovanje, štampanje, hranu, elektroniku, instrumentaciju, medicinsku opremu, industriju odeće proizvodna linija pogonskih uređaja za kontrolu brzine. Karakteristike: - Model: UX-52/003 - Ulaz: 240 VAC / 50/60 Hz - Maksimalna snaga: 400 W - Maksimalna struja: 3A - Dimenzije: 116 x 100 x 60 mm - Povezivanje: 5 žica Povezivanje: - L i N - 220V napajanje - faza i nula - U1 - Crna žica - Spoj glavnog namotaja motora i pomoćnog namotaja - U2 - Crvena žica - Spoj Pomoćnog namotaja i kondenzatora motora - Z2 - Bela žica - Spoj glavnog namotaja motora i kondenzatora - S1 i S2 - Plave žice - Tahometarski povratni napon sa motora - 0V - izlaz za spoljne prekidače za smerove FWD (napred) ili REV (nazad) Poseduje meni u koji se ulazi na dug pritisak tastera MODE i na ENTER promena istoga strelicama: F-01 - Parametri ubrzanja F-02 - Ubrazanje i ciljana vrednost F-03 - Controlni mod tasterima ili displejom F-04 - Mod nared nazad i koji je omogućen F-05 - Suprotna rotacija DA/NE F-06 - Promena brzine F-07 - Maksimalna ograničena brzina F-08 - Minimaln ograničena brzina F-09 - Vreme ubrzanja F-10 - Kočenje ili slobodno zaustavljanje moda napred F-11 - Vreme zaustavljanja moda napred F-12 - Vreme reverznog starta F-13 - Kočenje ili slobodno zaustavljanje moda nazad F-14 - Vreme zaustavljanja moda nazad F-15 - Alarm F-16 - Ciklična rotacija F-17 - Broj rotacija F-18 - Rotacijsko vreme napred F-19 - Rotacijsko vreme nazad F-20 - Operacioni interval F-21 - Brzina rotacije napred F-22 - Brzina rotacije nazad F-23 - Reset na fabrična podešavanja