56. *Bakarna pletenIca WICK, traka za odlemljavanje sirine 3.0 mm -duzine 1.5m. Neophodna alatka za upijanje suvisnog kalaja. U ponudi imam i bakarne pletenice od 1.5mm, 2.0mm, 2.5mm, 3.0mm. Pogledajte sve moje oglase. *Robu šaljem kao preporučeno pismo u vazdusnoj koverti sa pracenjem, cime je postarina samo 200din. (na Vašu odgovornost) nakon uplate na moj racun ili Postexpressom kurirskom sluzbom (pouzećem) robu placate prilikom preuzimanja. Naravno moze i licno preuzimanje kome vise odgovara. *Molim za komunikaciju preko K. P. poruka.

Native Instruments Multicore kabl sa slika.

Ispravno

Ispravno

Ispravno

Ispravno

Ispravna napojna ploca BN44-003009A.

- Instalaciona brza klema za spajanje žica, - 1 Ulazni priključak/5 izlaznih priključaka, - Materijal kontakata: bakar, - Maksimalna struja: 32A, - Maksimalni radni napon: 250VAC, - Odgovara kablovima poprečnog preseka 0.08-4mm2, - Boja: Siva, - Materijal Izrade: Plastika.

- Vodootporna kapa za prekidače, - Boja: Transparentna, - Odgovara mrežnim prekidačima ugradnih dimenzija 30x22mm.

Ispravno napajanje za monitor NE ŠALJEM PREDMETE VAN TERITORIJE SRBIJE! NAKNADNE REKLAMACIJE NE PRIHVATAM!

Ispravno napajanje za monitor NE ŠALJEM PREDMETE VAN TERITORIJE SRBIJE! NAKNADNE REKLAMACIJE NE PRIHVATAM!

BN96-25565A Zvučnici za Samsung UE40F6100 i slične 6 Ohm / 10 W

JUC7.820.00213099 glavna Alpha 32D5TDG. Ispravna, skinuta sa televizora kome je polupan panel.

OČUVAN STALAK ZA NOTE, BEZ OŠTEĆENJA

P06 Feature: With a wide input voltage range from 6V to 40V, the step-down converter can accurately adjust output voltage and current. The efficiency can be up to 96%, measured at 20A, converting 24V to 12V. It is designed with 75V/80A large current dual MOS tube. Input and output use high frequency low resistance electrolytic capacitor, low ripple, stable output. Wiring is convenient with these large current 30A screw terminals. The buck module has 2 heat sink that could enhance heat dissipation. When there is a big difference between input and output voltage, please decrease power and current. Specification: Input Voltage: 6V to 40V DC(10V to 40V is suggested) Output Voltage: 1.2V to 36V DC Output Current: 15A(suggested) Efficiency: 95%(24V to 12V, 20A) Output Ripple: ≤50mV Wiring Method: Terminal Short Circuit Protection: Self-recovery(cannot short circuit for long time) Size: 60 x 53 x 27mm / 2.36 x 2.08 x 1.06` VO+: Output positive VO-: Output negative +IN: Input positive -IN: Input negative CV: Output voltage adjustment CC: Output current adjustment EN: Enable, low voltage level shut off output; suspension, high voltage level is effective When input and output is common grounded, no-load CV output constant voltage,CC output constant current

KUPUJTE BEZBEDNO I KUPUJTE PROVERENO! POGLEDAJTE MOJE OCENE! SALJEM POSTEKSPRESOM i BEX-om SIROM SRBIJE! MOGUCE LICNO PREUZIMANJE I TESTIRANJE U INDJIJI I NOVOM SADU! Art Tech adapter 6V 350mA, konektor kao sa slika. Model: 41MCD01G Input: 230V ~ 50Hz 0.5A Output : 6V 350mA 2.1VA Original Netzteil AC-DC Adaptor Art-Tech 41MCD01G Potpuno ispravan i testiran. Radna garancija 30 dana. Podrzani modeli uredjaja: Pirastro 41MD31 Pirastro Tonica i Gold Vondertone Violin Stringing Transformateur 6V on-tech modè le V41-06D-550 EAN 0000020047573

- Nagazni prekidač (za gitarske pedale), - Tip kontakata: 3PDT, - Broj pinova: 9, - Boja: plava, - Maksimalna struja prekidanja: 4A, - Prečnik navoja: 12mm, - Dimenzije: 43x20x17mm.

Ispravno napajanje skinuto sa VOX-A

P16 XY-WTH1Temperature and humidity control module high precision digital display word double output automatic constant temperature and humidity control panel Product adopts industrial-grade chip, high-precision SHT20 temperature and humidity sensor. Product Function: Product features are two main types of classification: the functions of temperature and humidity; Function of temperature are as follows: The automatic identification of work mode: The system automatically according to the start/stop temperature, identify work mode; Start temperature > stop temperature, cooling mode`C`. Start temperature < stop temperature, heating mode `H`. Cooling mode: When the temperature≥Start temperature,relay conduction,red led on, refrigeration equipment begin to work; When the temperature≤Stop temperature,relay disconnect, red led off, refrigeration equipment stop to work; Heating mode: When the temperature≤Start temperature,relay conduction, red led on, heating equipment begin to work; When the temperature≥Stop temperature,relay disconnect, red led off, heating equipment stop to work; Temperature correction function OFE (-10.0 ~ 10℃): The system is working for a long time and may be biased, through this function correction, the actual temperature = measuring temperature + calibration value; How to set the start/stop temperature: 1. In the running interface, Long Press ` TM+ ` key more than 3 seconds, into the start temperature settings interface, can be modified by TM+ TM-key, to be modified, waiting for 6s automatic exit and save; 2. In the running interface, Long Press ` TM-` key more than 3 seconds, into the stop temperature settings interface,can be modified by TM+ TM-key, to be modified after the parameters, waiting for 6s automatic exit and save; The humidity function is as follows: The automatic identification of work mode: The system automatically according to the start/stop humidity, identify work mode; Start humidity> stop humidity, dehumidificationmode`D`. Start humidity< stop humidity, humidificationmode `E`. Dehumidificationmode: When the humidity≥Start humidity,relay conduction, green led on, dehumidification equipment begin to work; When the humidity≤Stophumidity,relay disconnect, green led off, dehumidificationequipment stop to work; Humidificationmode: When the humidity≤Start humidity,relay conduction, green led on, humidificationequipment begin to work; When the humidity≥Stophumidity,relay disconnect, green led off, humidificationequipment stop to work; Humidificationcorrection function RH (-10.0 ~ 10%): The system is working for a long time and may be biased, through this function correction, the actual humidity= measuring humidity+ calibration value; How to set the start/stop humidity: 1. In the running interface, Long Press ` RH+ ` key more than 3 seconds, into the start humiditysettings interface, can be modified by RH+ RH- key, to be modified, waiting for 6s automatic exit and save; 2. In the running interface, Long Press ` RH-` key more than 3 seconds, into the stop humiditysettings interface, can be modified by RH+ RH- key, to be modified after the parameters, waiting for 6s automatic exit and save; Running Interface Description: Working mode shows that the current mode (`H/C`, `E/d`) will be synchronized at the front of temperature/humidity, when the setting of temperature/humidity and stop temperature/humidity are completed. Any relay conduction, the upper-left corner of the interface display `out`, if the temperature relay conduction, the flashing display temperature working mode `H/C` to show reminders; if the humidity relay conduction, then flashing display humidity working mode `E/d`, as a reminder; Other features: Parameter remote read/set: Through the UART, set the starting temperature/humidity, stop temperature/humidity, temperature/humidity correction parameters; temperature/Humidity Real-time reporting: If the temperature/humidity reporting function is turned on, the product will detect the temperature/humidity and relay status by the 1s interval, and pass the UART to the terminal to facilitate data collection; Relay enabling (by default): If the relay is disable, the relay remains disconnected; How to modify the temperature/humidity correction value: 1. In the operating interface, double-click the ` TM+ ` key to enter the correction of the set interface, the downward display correction of the type, the upward display of specific values; (OFE: Temperature correction value RH: Humidity correction value) At this time by a short press ` TM-` key, switch to modify the parameters, through the RH+ RH-key, modify the specific value of the support long press short; 3. When the parameters have been modified, double-click the ` TM+ ` key, exit the correction positive setting interface, and save the data; How to enable/disable relay: In the running interface, Short press ` TM-` key,enable/disablethe temperature relay(ON: enableOFF:disable), back to the running interface, if the temperature relay is disable, the temperature symbol ` ℃ ` flashes to remind. In the running interface, Short press ` RH-` key, enable/disable the humidity relay (ON: enable OFF: disable), back to the running interface, if the humidity relay is disable, the humidity symbol `% ` flashes, as a reminder. Serial control(TTL level) BaudRate:9600bps Data bits :8 stop bits :1 crc :none Flow control :none

Ispravna matična ploča NE ŠALJEM PREDMETE VAN TERITORIJE SRBIJE! REKLAMACIJE NE PRIHVATAMO!

- Vrh namenjen za WELLER lemilicu WLG940023C.

Ispravno NE ŠALJEM PREDMETE VAN TERITORIJE SRBIJE! NAKNADNE REKLAMACIJE NE PRIHVATAM!