Dot Led matriks modul 8x8 sa MAX7219 cetvorostruki. Modul dolazi kompletno sklopljen i sa kablicima. Product Description The MAX7219 are compact, serial input/output common-cathode display drivers that interface microprocessors (μPs) to 7-segment numeric LED displays of up to 8 digits, bar-graph displays, or 64 individual LEDs. Included on-chip are a BCD code-B decoder, multiplex scan circuitry, segment and digit drivers, and an 8x8 static RAM that stores each digit.Only one external resistor is required to set the segment current for all LEDs. The MAX7219 is compatible with SPI™, QSPI™, and Microwire™, and has slew-ratelimited segment drivers to reduce EMI.A convenient 3-wire serial interface connects to all common μPs. Individual digits may be addressed and updated without rewriting the entire display. The MAX7219 also allow the user to select code-B decoding or no-decode for each digit.The devices include a 150μA low-power shutdown mode, analog and digital brightness control, a scanlimitregister that allows the user to display from 1 to 8 digits, and a test mode that forces all LEDs on. Features: A single module can drive a 8x8 dot matrix common cathode Module Working voltage: 5V Module size: 12.8 cm X3.2 cm X1.3 cm(L*W*H) With 64 fixing screw holes, Hole diameter 3mm Module with input and output interfaces, support for cascading multiple modules Wiring:for example 51 SCM VCC→5V GND→GND DIN→P2.2 CS →P2.1 CLK→P2.0

60219 Kvalitetan daljinski upravljač napravljen u kombinaciji metal - plastika. Može da se koristi za bezbedonosne sisteme, automobile, rolo vrata, klizajuće kapije, roletne i razne kućne aparat. Kućište sa prekrivačem za tastere. Frekvencija: 433.92 MHz Napajanje: 1 x 27A baterija (u sklopu) Kodovi: Fiksni Dimenzije: 51x26.5x11.8 mm Ostale napomene: Kod se ne gubi nakon zamene baterija Kodira se na sledeći način - Prvo se resetuje daljinski kako bi mogao da se iskopira kod sa starog daljinskog. To se radi tako što se drže istovremeno tasteri A i B (odnosno 1 i 2) preko 2 sekunde, lampica će blinkati, i time se brišu postojeći ili fabrički kodovi u samom daljinskom. nakon toga uzmite stari daljinski i prislonite na novi daljinski na koji želite da kopirate kodove (moraju biti na manje od 1cm jedan od drugog) na novom daljinskom pritisnite i držite pritisnutim dugme koje želite da iskopirate i koristite, i držite pritisnutim svo vreme kopiranja (lapmica će jednom zasvetleti, nakon toga može primiti kod). Svo vreme dlajinski moraju biti jedan pored drugog. pritisnite dugme na starom daljincu sa kog želite da iskopirate kod, svo vreme držeći dugme na novom daljinskom, dok lampica na novom daljinskom ne zatreperi što znači da je kod iskopiran. Kopiranje traje kratko, manje od sekunde. Napomena: tasteri A i B se moraju pritisnuti istovremeno, ako ima vremenskog rastojanja većeg od delića sekunde, neće se resetovati. Za kopiranje se mora prvo pritisnuti i držati taster na starom, pa na novom daljinskom i onda će se iskopirati.

Ovaj modul je namenjen za projekte gde se trebaju povezati serijski protokol sa WiFi mogućnostima, uz podršku jedno 32 bitnog MCU-a. Podržava Wifi b g i n protokole. Tehničke karakteristike: Built-in Tensilica L106 ultra low power 32-bit micrMCU, with 16-bit streamlined mode, clocked at 80 MHz and 160MHz, support RTOS WIFI @ 2.4 GHz, support WPA / WPA2 security mode Built-in 10 bit high precision ADC Built-in TCP / IP protocol stack Built-in TR switch, balun, LNA, power amplifier and matching network Built-in PLL, regulator and power management components 802.11b mode + 20 dBm output power Supports antenna diversity The deep sleep hold current is 20uA and the shutdown current is less than 5uA can be doubled as application processor SDI2.0, SPI, UART STBC, 1x1 MIMO, 2x1 MIMA-MPDU, A-MSDU aggregation and 0.4 s protection interval Within 2ms wake up, connect and pass the packet standby power consumption less than 1.0mW (DTIM3) support AT remote upgrade and cloud OTA upgrade Supports STA / AP / STA + AP operation mode Šifra: B1120

Ovaj programator je namenjen programiranju 8-pinskih SPI fleš memorija kao što su W25Q32, W25X80 i mnoge druge. Pored svoje osnovne mogućnosti, ovaj programator podržava i programiranje I2C serijskih EEPROM-a familije 24CXX ( 24C01, 24C02, 04, 08 . . . 24C1024 ). Spisak podržanih kola: http: //bleha. net/sw/usbspifl. txt Komplet sadrži: - Zalemljen i ispitan modul programatora - 2 različite SMD adapter ploče USB 2.0 interface, The speed of reading and writing is very fast. support WIN98 ，WINME ，WIN2K ，WINXP ，VISTA ，WIN7 32bit/64bit Speed: 2-3M/min Using recoverable automatically fuse the event of the the chips short-circuit or chip installed anti will automatically power off ( indicator turns off ) to avoid motherboard , programmer and chip burn out , short circuit exclude automatic recovery Working Voltage: 5V mini-B connecor CH341A as the main chip, this module has good Quantity Support 24,25 series chips USB to TTL could be used to download code Two Function: TTL and Program Power indicator Recoverable fuse automatically: when the chip is in short-circuit or installed wrongly, the fuse will be used to protected the chip unless the error has been corrected. POGLEDAJTE JOS NASIH OGLASA! NAJJEFTINIJE U SRBIJI - PROVERENO!

Uređaji su stigli u stanju kao na slikama(jedan bez oštećena drugi oštećen), oštećenje se vidi na slikama. Nemam odgovarajuće kablove da ih probam(ništa nije probano) pa ide kao neproveren bez reklamacija. Inače to su multifunkcionalni uređaji rekorderi, ruter(2,4 i 5ghz) telefonski priključci i mnoštvo drugih priključaka. Jedan Ide sa orginalnim daljincem koji reaguje kad se klikne dakle verovatno ispravan drugi bez. Horizon HD Recorder technical data: Colour: Black HDTV: Yes Hard disk memory: 500 GB, 400 GB is available for up to 90 hours of recording in HD or 180 hours of recording in SD SmartCard: No (virtual smart card) Number of tuners: 6 (4 for parallel recordings) DOCSIS module: Puma 5 WiFi: 802.11 a / b / g / n Frequency: 2.4 GHz and 5.0 GHz (parallel operation) On/off switch: Yes Dimensions: 376.5 x 300 x 60 mm Weight: 2.5 kg Energy consumption: In operation: max. 59 W High (active) standby: 56 W High (passive) standby: 38.3 W Medium standby: 27.5 W Low standby mode (quick start): 2.6 W Low standby: 1 W Connections: Coaxial input: (RF IN) 1 Coaxial output: (RF OUT) 0 HDMI port for top-quality audio and video: 1 Digital audio coaxial socket (S/PDIF coaxial): 1 Optical digital audio socket (S/PDIF optical): 1 Network ports (Ethernet/RJ45): 4 Telephone ports (RJ11): 2 USB ports: 2 (deactivated)

DALJINSKI - Loewe Control 150 TV Potpuno ispravan i testiran. Bez baterija - kupujete ih sami 2 x AAA 1,5V Radna garancija 7 dana. Podrzani modeli: LOEWE Control 150 - 200 - 100 - 201 LOEWE 58406V LOEWE 8784ZPARCADA LOEWE 9281ZWACONDA LOEWE ACONDA9272ZP LOEWE ACONDA9381ZW LOEWE ANACONDA9381 LOEWE ARCADA5684Z LOEWE ARCADA8672Z LOEWE ARCADA8672ZP LOEWE ARCADA8672ZPNICL LOEWE ARCADA8684 LOEWE ARCADA8684ZP LOEWE ARCADA8684ZP LOEWE ARCADA8772ZP LOEWE CALIDA5255 LOEWE CALIDA5255 LOEWE CALIDA5655Z LOEWE CALIDA5663Z LOEWE CALIDA5672Z LOEWE CALIDA5684Z LOEWE CALIDA5684Z LOEWE CALIDA5722 LOEWE CALIDA5772 LOEWE CALIDA5784ZP LOEWE CANTUS3872ZP LOEWE CANTUS3872ZP LOEWE CONTUR1670Z LOEWE CONTUR76 LOEWE CREDO7570ZP LOEWE CREDO7570ZPH LOEWE CREDO7581ZP LOEWE CREDO7581ZPH LOEWE CT1570Z LOEWE ERGO6670ZP LOEWE ERGO6672ZP LOEWE ERGO6681ZP LOEWE EVOLUTION8102 LOEWE PLANUS4663Z LOEWE PLANUS4670Z LOEWE PLANUS4672Z LOEWE PLANUS4681Z LOEWE PLANUS4681ZNICL LOEWE PLANUS4681ZP LOEWE PLANUS4781ZPW LOEWE PLANUS4872Z LOEWE PROFIPLUS3472 LOEWE PROFIL3563Z LOEWE PROFIL3563Z LOEWE PROFIL3563Z LOEWE PROFIL3570Z LOEWE PROFIL3572Z LOEWE PROFIL3572ZP LOEWE Q2300 LOEWE VITROS6381ZP LOEWE VITROS6381ZW LOEWE XELOS5261ZW LOEWE XELOS5270ZW LOEWE XELOS5281ZW Loewe Control 100 Control 150 Calida 5755 Z Calida 5763 Z Calida 5763 Z Calida 5772 ZP Calida 5772 ZP Calida 5784 ZP Cantus 3870 ZW Cantus 3870 ZW Cantus 3872 ZP Cantus 3872 ZP Cantus 3872 ZP Contur 1663 Z Contur 1670 Z Contur 1670 Z Melody 7205 Z Planus 4663 Z Planus 4670 ZP Planus 4672 ZP Planus 4672 ZP Planus 4872 Z Profil 3563 Z Profil 3563 Z Profil 3570 ZWP Profil 3570 ZWP Profil 3572 Z Profil 3572 Z Vitros 6370 ZWP Vitros 6370 ZWP Vitros 6372 ZP Vitros 6372 ZP Xelos 5255 Z Xelos 5261 ZW Xelos 5270 ZWP Q2500 Q2500 B TV

Pogodan za utiicnice i dozne , radi na naizmenicnu struju , pogodan na prekidace sa dva prekida , obicne prekidace , i još mnoge , staje u standardnu doznu , ima opciju tajmera 24h Podržane aplikacije smartlife i tuya Opis: 1. Kontrola mobilne aplikacije Kontrolišite prekidač, vreme, odbrojavanje i druge funkcije uređaja preko mobilnog telefona. 2. Upravljanje glasom. Podržite glasovne asistente kao što su Tmall Vizard, Aleka, GoolHome, itd. , za realizaciju funkcija kao što su prekidači; 3. Daljinski upravljač. Može da realizuje daljinsko upravljanje svetlom putem mobilnog telefona, bez obzira gde se nalazite na zemlji, sve dok se vaš mobilni telefon može povezati na mrežu, možete ga kontrolisati; 4. Tehnologija umrežavanja. Jedan mobilni telefon može da kontroliše više prekidača, a jedan prekidač može da kontroliše više mobilnih telefona u isto vreme; 5. Grupna kontrola. Svetla se mogu grupisati da bi se postigla jedinstvena kontrola (istovremeno prebacivanje, vreme itd. ); 6. Internet svega. Preko podešavanja, može se povezati sa drugim inteligentnim scenama kako bi život bio pametniji; 7. Deljenje i bezbednost. Glavni nalog se može deliti sa drugim članovima porodice, a funkcije i podešavanja se u potpunosti zadržavaju i kopiraju; bezbednost: kada se lampa doda na glavni nalog, lampa će biti i drugi korisnici više neće moći da pronađu i dodaju; mora se aktivno deliti pre nego što drugi mogu da ga koriste. Povezuje se aplikacijom Smart Life ili Tuya Smart. Lako se povezuje unutrar postojeceg prekidača. Voltaza: 100-240V 50/60Hz Max. opterecenje: 16A WiFi Standard: 2.4GHz 802.11 b/g/n Dimenzije: 42*42*20mm u Paket je uključen: 1 mini modul pametnog prekidača, 1 priručnik

Pogodan za utiicnice i dozne , radi na naizmenicnu struju , pogodan na prekidace sa dva prekida , obicne prekidace , i još mnoge , staje u standardnu doznu , ima opciju tajmera 24h Podržane aplikacije smartlife i tuya Opis: 1. Kontrola mobilne aplikacije Kontrolišite prekidač, vreme, odbrojavanje i druge funkcije uređaja preko mobilnog telefona. 2. Upravljanje glasom. Podržite glasovne asistente kao što su Tmall Vizard, Aleka, GoolHome, itd. , za realizaciju funkcija kao što su prekidači; 3. Daljinski upravljač. Može da realizuje daljinsko upravljanje svetlom putem mobilnog telefona, bez obzira gde se nalazite na zemlji, sve dok se vaš mobilni telefon može povezati na mrežu, možete ga kontrolisati; 4. Tehnologija umrežavanja. Jedan mobilni telefon može da kontroliše više prekidača, a jedan prekidač može da kontroliše više mobilnih telefona u isto vreme; 5. Grupna kontrola. Svetla se mogu grupisati da bi se postigla jedinstvena kontrola (istovremeno prebacivanje, vreme itd. ); 6. Internet svega. Preko podešavanja, može se povezati sa drugim inteligentnim scenama kako bi život bio pametniji; 7. Deljenje i bezbednost. Glavni nalog se može deliti sa drugim članovima porodice, a funkcije i podešavanja se u potpunosti zadržavaju i kopiraju; bezbednost: kada se lampa doda na glavni nalog, lampa će biti i drugi korisnici više neće moći da pronađu i dodaju; mora se aktivno deliti pre nego što drugi mogu da ga koriste. Povezuje se aplikacijom Smart Life ili Tuya Smart. Lako se povezuje unutrar postojeceg prekidača. Voltaza: 100-240V 50/60Hz Max. opterecenje: 16A WiFi Standard: 2.4GHz 802.11 b/g/n Dimenzije: 41*41*20mm u Paket je uključen: 1 mini modul pametnog prekidača, 1 priručnik

P12 1. Support Lead-acid battery and Acting Battery,voltage range:6V~60V; 2. Can display voltage,percent of battery,charging time at the same time through LCD; 3. The function is very powerful,realizes the automatic charge control, the control charge time, also may set up and uploads the corresponding parameter through the serial port; Function description 1. Automatic Charge control function: By setting the volt-HI:`UP` volt-LI:`dn`;When the battery voltage is below the volt-LI:`dn`,the relay leads,the charger begins to charge the battery;when the battery voltage is up to volt-HI:`UP`,the relay is diconnected and the automatic charge is completed once; 2. Charge Time Control Function: How to turn on the time control function? After entering the parameter set, set the parameter op is non-zero, then turn on the time control function, op default parameter is:--:--h, the default does not turn on time control function; After the opening Time control function (OP is non-zero), when the battery voltage is the lower volt-LI`dn`, the charger began to charge the battery, the system began to clock; During the timing, the battery voltage ≥ volt-HI`UP`, relay disconnect; If the OP time is up, the battery voltage is still the lower volt-LI`dn`, the relay keeps the conduction, automatically closes the charge time control function, and flashes the H:ER to remind the user, the time parameter setting is unreasonable; Press any key to stop flashing; Note: Time format: 00:59 (00 for hours, 59 for minutes) The maximum time is 99:59, which is 100 hours. 3. Serial data upload and parameter setting function: The system supports UART data upload and parameter setting UART:115200,8,1 Cmd Func on Relays enable to open off Relays disable to open start Start data upload stop Stop data upload read Read the param setting dw10.0 Set volt-LI:`dn` up20.0 Set volt-HI:`UP` xx:xx Set the charge time OP 00:00 stop charge time Data Upload message Format: Battery voltage + battery percent + charge time + charge status 12.0V,020%,00:10,OP Parameter Setting a) Press and hold the SET key to enter the setting interface; b) Switch the parameters you want to set by short press SET; c) After the selection of parameters, can be set by the UP/DOWN key to support the short press, long press (fast increase or decrease); To set other parameters, repeat step b, c); d) After all parameters are set, long press set key to exit and save; The Key Function Description: In the Run interface (main interface): Short press SET button to display the current set of parameters; Short press UP button, toggle display charge percentage and charging time; Short Press DOWN button, select Turn on/off relay enabling, if the relay can be closed, will show ` off ` as a reminder; Long press UP button, switch low power state on:No operation in 10 minutes turn off backlight OFF: Backlight is always bright Long press SET button,enter the parameter settings. Calculation of voltage percentage: voltage percentage = battery voltage/(volt-HI – volt-LI) Additional Features a) Charging time recording function: not open charging time control, the product will record a full time, when the entry time display interface, flashing display charging time, and then exit time display interface or next charge to open (relay conduction) when empty; b) Automatic parameter detection: When the parameters are set, exit, if volt-LI dn≥ volt-HI UP, the system will flash display `ERR` as a reminder; c) Battery Access detection: This product attached to the battery, if not connected to the battery, the system will be shown in the downlink `NbE` as a reminder Analysis of common failures Q: How much is suitable for V level use? How much v voltage does this module fit? A: This section is suitable for the minimum 6V, the highest 60V voltage range, the maximum expenditure level 48V, because 48V battery full of electricity in 60V, and then a high fever, if your battery is higher than 48V, please select other section. Q: The power of the subsequent electrical appliances snapped! LED flashing? A: This is because your charging current is too large or the battery capacity is too small to cause a power to immediately reach the voltage limit, relay disconnect, disconnect, the voltage and quickly down to the lower voltage, and began to recharge, cycle, at this time you want to reduce the charging current only line, Usually the charging current is the battery capacity of the very 1 to 1.5, such as 20AH battery charging current generally around 2-3a! Note that a large current charge will cause the battery fever accelerated aging, drum kits and even explosions! Q: What control mode? Can I cycle the charge automatically? Can I use the side charge? Can I limit the flow? A: This is voltage control, For example, set the voltage limit of 12.0V, voltage up to 14.5V, voltage charge to 14.5V this value on the power off, voltage down to the 12.0V relay closed and start charging, can be filled with side, voltage control mode only to turn off and open, can not limit the flow, charging current completely depends on your charger! Q: Input 12V can or not charge 24V battery, or enter 48V can give 12V battery charge? A:This is a simple voltage controller, only play the role of switch, can not swing to the battery charge, so you want to give what battery charge to be ready what kind of charger! It`s necessary!

P01 1. Support Lead-acid battery and Acting Battery,voltage range:6V~60V; 2. Can display voltage,percent of battery,charging time at the same time through LCD; 3. The function is very powerful,realizes the automatic charge control, the control charge time, also may set up and uploads the corresponding parameter through the serial port; Function description 1. Automatic Charge control function: By setting the volt-HI:`UP` volt-LI:`dn`;When the battery voltage is below the volt-LI:`dn`,the relay leads,the charger begins to charge the battery;when the battery voltage is up to volt-HI:`UP`,the relay is diconnected and the automatic charge is completed once; 2. Charge Time Control Function: How to turn on the time control function? After entering the parameter set, set the parameter op is non-zero, then turn on the time control function, op default parameter is:--:--h, the default does not turn on time control function; After the opening Time control function (OP is non-zero), when the battery voltage is the lower volt-LI`dn`, the charger began to charge the battery, the system began to clock; During the timing, the battery voltage ≥ volt-HI`UP`, relay disconnect; If the OP time is up, the battery voltage is still the lower volt-LI`dn`, the relay keeps the conduction, automatically closes the charge time control function, and flashes the H:ER to remind the user, the time parameter setting is unreasonable; Press any key to stop flashing; Note: Time format: 00:59 (00 for hours, 59 for minutes) The maximum time is 99:59, which is 100 hours. 3. Serial data upload and parameter setting function: The system supports UART data upload and parameter setting UART:115200,8,1 Cmd Func on Relays enable to open off Relays disable to open start Start data upload stop Stop data upload read Read the param setting dw10.0 Set volt-LI:`dn` up20.0 Set volt-HI:`UP` xx:xx Set the charge time OP 00:00 stop charge time Data Upload message Format: Battery voltage + battery percent + charge time + charge status 12.0V,020%,00:10,OP Parameter Setting a) Press and hold the SET key to enter the setting interface; b) Switch the parameters you want to set by short press SET; c) After the selection of parameters, can be set by the UP/DOWN key to support the short press, long press (fast increase or decrease); To set other parameters, repeat step b, c); d) After all parameters are set, long press set key to exit and save; The Key Function Description: In the Run interface (main interface): Short press SET button to display the current set of parameters; Short press UP button, toggle display charge percentage and charging time; Short Press DOWN button, select Turn on/off relay enabling, if the relay can be closed, will show ` off ` as a reminder; Long press UP button, switch low power state on:No operation in 10 minutes turn off backlight OFF: Backlight is always bright Long press SET button,enter the parameter settings. Calculation of voltage percentage: voltage percentage = battery voltage/(volt-HI – volt-LI) Additional Features a) Charging time recording function: not open charging time control, the product will record a full time, when the entry time display interface, flashing display charging time, and then exit time display interface or next charge to open (relay conduction) when empty; b) Automatic parameter detection: When the parameters are set, exit, if volt-LI dn≥ volt-HI UP, the system will flash display `ERR` as a reminder; c) Battery Access detection: This product attached to the battery, if not connected to the battery, the system will be shown in the downlink `NbE` as a reminder Analysis of common failures Q: How much is suitable for V level use? How much v voltage does this module fit? A: This section is suitable for the minimum 6V, the highest 60V voltage range, the maximum expenditure level 48V, because 48V battery full of electricity in 60V, and then a high fever, if your battery is higher than 48V, please select other section. Q: The power of the subsequent electrical appliances snapped! LED flashing? A: This is because your charging current is too large or the battery capacity is too small to cause a power to immediately reach the voltage limit, relay disconnect, disconnect, the voltage and quickly down to the lower voltage, and began to recharge, cycle, at this time you want to reduce the charging current only line, Usually the charging current is the battery capacity of the very 1 to 1.5, such as 20AH battery charging current generally around 2-3a! Note that a large current charge will cause the battery fever accelerated aging, drum kits and even explosions! Q: What control mode? Can I cycle the charge automatically? Can I use the side charge? Can I limit the flow? A: This is voltage control, For example, set the voltage limit of 12.0V, voltage up to 14.5V, voltage charge to 14.5V this value on the power off, voltage down to the 12.0V relay closed and start charging, can be filled with side, voltage control mode only to turn off and open, can not limit the flow, charging current completely depends on your charger! Q: Input 12V can or not charge 24V battery, or enter 48V can give 12V battery charge? A:This is a simple voltage controller, only play the role of switch, can not swing to the battery charge, so you want to give what battery charge to be ready what kind of charger! It`s necessary!

Naponsko strujni i strujno naponski modul 4-20mA. Za prenos podataka na vece daljine i sa vecom sigurnoscu se koristi naposno strujna konverzija u opsegu 4-20mA. Na oba modula se jednim trimerom podesava nula a drugim struja, odnosno napon u odnosu na zeljeni ulazni napon, odnosno struju. U kompletu idu dva modula, naponsko-strujni i strujno-naponski. Current to Voltage Converter 4-20 mA 0-15V Voltage switch current module can convert 0-3.3V / 0-5V / 0-10V / 0-15V voltage signal into 4-20ma current signal; In the process of signal transmission circuit voltage signal will increase transmission distance becomes weak, the transmission can be avoided using weak electric current signal. 1. power supply voltage range of DC 7V ~ 30V 2. the input voltage signal 0 ~ 2.5V, 3.3V, 5V, 10V, 15V. 3. the output current 4-20ma. 4. zero and span can be adjusted (potentiometer adjustment). 5. with the isolated nature of the non-optically isolated. 6. module size: 3.3 * 2.5cm Description: Voltage switch current module can convert 0-5V voltage signal into 4-20mA current signal. In the process of signal transmission circuit voltage signal will become weak with transmission distance increased, the transmission can be avoided using weak electric current signal. Power supply voltage: DC 12V~24V. Input voltsge signal: 0~5V. Output current: 4-20mA. Module size :5.5*2.5cm zero and span can be adiusted (potentiometer adjustment). with the isolated nature of the non-optically isolated. Input and output linear equations: To convert the voltage and output current is a linear relationship, according to the zero point and adjust the range to determine the linear equation, two points to determine a straight line, two points are zero and adjust the range. Iout = K * V + b. For example: 0-10V will be converted to 4-20mA, two points (0.4) and (10.20) which can determine the linear equation I = 1.6 * V +4. Product manual: 1: get the baby power supply module connected to the right side of the three terminals. 2: zero: the conversion voltage signal is adjusted to 0V, adjust the zero reset device to make the output current 4ma. It is best to adjust the potentiometer knob with glue. 3: Tuning: adjust the conversion voltage to the required full-scale voltage (such as 3.3V, 5V, 10V, 15V), will adjust the full potentiometer so that the output current can be 20ma. The adjustment process will find the current output indicator from weak to strong. It is best to adjust the potentiometer knob with glue. 4: input voltage within the range, you can output the corresponding current, and the output current is negative for the power supply. Example of adjustment: For example: the supply voltage of 24V, need to 0-10V into 4-20mA 1: connected to the power supply voltage 24V, 24V positive connected to the right side of the three terminals, the negative side of the right end of the three terminals. 2: Zero: Two short terminals on the left side, adjust the zero knob to make the output (middle three terminals on the right) 4mA. 3: adjust the range: the need for conversion on the left side of the 10V, the left side of the need to convert the voltage of the negative pole. Adjust the span knob so that the output (middle three terminals on the right) is 20mA. 4: to change the voltage in the 0-10V change, the output current in the 4-20mA linear changes.

P04 Product Highlights: 1. Display with LCD two columns, Can display parameters directly; 2. Trigger mode: high and low level,switch quantity.meet most of the needs. 3. Power supply: 6~30V, also supports micro USB 5.0V, very convenient.Anti back connection of power supply. 4. Parameters can be modified via UART. 5. Stop button to provide emergency stop function. 6. 5 minutes without any operation into a low-power state. Any action wake up. 7. OP/CL/LOP params can be modified individually 8. All parameters are automatically saved by power off. Working Mode Introduction(P1~P7) P1: After the signal is triggered, the relay conduction in OP time then disconnects; In the OP time, the signal is invalid. P2: After the signal is triggered, the relay conduction in OP time then disconnects; In the OP time, the signal triggers a new timer. P3: After the signal is triggered, the relay conduction in OP time then disconnects; In the OP time, signal trigger reset timer,relay disconnected and stop timing. P4: When triggered, After the relay is disconnected from CL time, relay conduction OP time, after timing is complete, disconnect relay. P5: When triggered, After the relay conduction op time, the relay disconnects the CL time, and then loops the above action, gives the signal again in the loop, relays disconnect, stops the timer, and the number of cycles (LOP) can be set; P6: When triggered, After the relay conduction op time, the relay disconnects the CL time, and then loops the above action, signal is invalid in the loop, the number of cycles (LOP) can be set; P7: Signal hold function: The signal is maintained, the timing is cleared, and the relay conduction; when the signal disappears, the relay disconnects after the timing OP; during the timing, there is another signal and the timing is cleared; Product Parameters: 1. Power Supply: 6V~30V and micro USB 5.0 V 2. Trigger signal source: High level(3.0V~24.0V),Low level(0.0V ~0.2V),Switch signal. 3. Maxmum Output load: DC 30V 5A and AC 220V 5A. 4. Static Current: 15mA Operating current: 50mA. 5. Service life: more than 100,000 times; working temperature: -40-85°C; size: 8.0*3.8*1.9cm. 6. Optocoupler isolation,Strong anti-interference ability, Industrial grade circuit board Timing Range: 0.01 sec~9999 min How to choose the timing range: In the OP/CL parameter modification interface, press the STOP button shortly to select the timing range. XXXX Timing range:1sec~9999sec XXX.X Timing range:0.1sec~999.9sec XX.XX Timing range:0.01sec~99.99sec X.X.X.X Timing range:1min~999.9min For example, if you want to set the OP to 3.2 seconds, move the decimal point to ten digits. LCD display 003.2 Parameter Description: OP on-time, CL off time, LOP cycle times (1 - 9999 times, `----` represents an infinite number of cycles) Parameter Settings: a) Press and hold the SET key to enter the setting interface; b) First set the working mode, work mode flashes reminder, set the working mode by pressing the UP / DOWN keys; c) Short press the SET button to select the working mode and enter the system parameter settings. d) In the system parameter setting interface, press SET key to switch the system parameters to be modified, and press / long press UP/DOWN key to modify. (Note: Short press SET in P-1~P-3, P-7 mode is invalid); e) In the OP/CL parameter modification interface, short press STOP to switch the timer unit (1s/0.1s/0.01s/1min); f) After all parameters are set, press and hold the SET button for more than 2 seconds to release the hand, save the parameter settings and exit the setting interface

KUPUJTE BEZBEDNO I KUPUJTE PROVERENO! POGLEDAJTE MOJE OCENE! SALJEM POSTEKSPRESOM i BEX-om SIROM SRBIJE! MOGUCE LICNO PREUZIMANJE I TESTIRANJE U INDJIJI I NOVOM SADU! Grunding TP 715 daljinski upravljac ORIGINAL za TV uredjaje. Model: TP 715 ili TP715 Nazalost nema zadnji poklopacdaljinskog sto se vidi na slici. Potpuno ispravan i testiran. Radna garancija 30 dana. Podrzava sledece Grunding TV uredjaje: CUC 2059 N CUC 2080 N E 72-170 IDTV M 55-280/8 IDTV/LOG M 63-115/9 IDTV M 63-281 IDTV/LOG M 63-281/8 IDTV/LOG M 70-1690 DPL/IDTV/LOG M 70-1690 TOP/LOG M 70-280 IDTV/LOG M 70-280/8 IDTV/LOG M 70-281 IDTV/LOG M 70-281/8 IDTV/LOG M 70-282 M 70-290 IDTV DAVIO 70 M 70-290/8 IDTV DAVIO 70 M 72-100 M 72-100 A M 72-100/8 M 72-100/8 A M 72-109 VNM M 72-115 IDTV M 72-115/9 IDTV PIP M 72-215 IDTV M 72-270 IDTV/LOG/EL M 72-315 IDTV REFERENCE M 72-315/9 IDTV REFERENCE M 72-400 DOLBY XENTIA 72 M 72-400/8 DOLBY XENTIA 72 M 72-410 REFERENCE M 72-410 PIP REFERENCE M 72-410/9 REFERENCE M 82-115/9 IDTV PIP M 82-269 PALPLUS/LOG M 84-210/8 A IDTV/LO M 84-210/8 IDTV M 84-210/8 IDTV/LOG M 84-211-8 IDTV M 95-115/9 IDTV PIP M 95-410/9 REF/PIP M 95-411/9 REF/PIP MF 55-5101 NIC/DOLBY XENTIA 55 FLAT MF 72-490 DOLBY XENTIA 72 FLAT MF 72-490/8 DOLBY XENTIA 72 FLAT MFW 70-490/8 DOLY XENTIA 70 FLAT MFW 70-530/9 DPL ARGANTO 70 FLAT MFW 82-490/9 DOLBY XENTIA 82 FLAT MFW 82-530/9DPL ARGANTO 82 FLAT MW 70-100/8 MW 70-2101 DOLBY ELEGANCE 70 MW 70-2101 NIC/DOLBY ELEGANCE 70 MW 70-269 PAL PLUS MW 70-2690 NIC/TOP MW 70-2699 NIC/FT MW 70-2699 NIC/TOP MW 70-2700 DOLBY MW 70-2700 NIC/DOLBY MW 70-510/8DPL ARGANTO 70 MW 82-100/9 PALPLUS MW 82-2101 DOLBY ELEGANCE 82 MW 82-2101 NIC/DOLBY ELEGANCE 82 MW 82-2690 NIC/TOP MW 82-2699 NIC/FT MW 82-2699 NIC/TOP MW 82-2700 DOLBY MW 82-2700 NIC/DOLBY MW 82-40/8 MW 82-50/8 MW 82-510/8DPL ARGANTO 82 P 37-080 P 37-2101 MV ARCANCE 37 P 37-2102 DAVIO 37 P 37-2102 MV DAVIO 37 P 37-2102/1 DAVIO 37 P 37-2103 MV DAVIO 37 P 37-4101 GB DAVIO 37 P 37-4101 MV DAVIO 37 P 37-4101 TOP DAVIO 37 P 37-4101 TOP/1 DAVIO 37 P 37-4101 TOP/TR DAVIO 37 P 37-4101/12 MV DAVIO 37 P 37-4101/12 MV/SAT DAVIO 37 P 37-830 TEXT P 37-830/12 TEXT GLOBETROTTER P 45-4101 TOP P 45-830 TEXT P 45-830/4 TEXT PW 110-520/9 PAL PLUS PLANATRON 2 S 55-806 TOP/TR SE 5587 TOP GREENVILLE 560 SE 5590 DOLBY GREENVILLE 561 SE 6320 IDTV/LOG WIEN 100 SE 70-100/8 BERLIN SE 7016/9 REF/PIP SE 7020 IDTV/LOG SYDNEY SE 7020/8 IDTV/LOG SYDNEY SE 7021 IDTV SE 7021 IDTV/PIP SIDNEY 100 SE 7030 GREENVILLE 100 SE 7050/8 PIP/DOLBY BERLIN SE 7089 IDTV/LOG SE 7090 IDTV/LOG BOSTON SE 7090/8 IDTV LOG BOSTON SE 7210 A/NIC/TOP MELBOURNE SE 7210 NIC/TOP MELBOURNE SE 7210 TOP MELBOURNE SE 7212 TOP MELBOURNE SE 7220 IDTV/LOG SE 7230 DOLBY SYDNEY 2000 SE 7240 DOLBY SIDNEY SE 7241 DOLBY SIDNEY FLAT SE 7250 PIP/DOLBY ATLANTA SE 7250/8 DOLBY ATLANTA SE 7277 TEXT SE 7289 IDTV/LOG ATLANTA SE 7290 IDTV/LOG BERLIN SE 82-100 PALPLUS DENVER SE 8216/9 REF/PIP SE 8240 DOLBY SE 8250/8 PIP/DOLBY DENVER SE 8270 DOLBY ST 25-8210/6 NT ST 270 IDTV/LOG BOSTON ST 270/8 IDTV/LOG BOSTON ST 28-8210/6 NT ST 55-400 DOLBY XENTIA 55 ST 55-400 NIC/DOLBY XENTIA 55 ST 55-405 DOLBY XENTIA 55 ST 55-4105 DOLBY LEEMAXX 55 ST 55-605 TOP ST 55-715 NIC/TOP ST 55-725 B FT/TOP ST 55-730 GB/DOLBY ST 55-734 GB/DOLBY ST 55-800 A TOP ST 55-805 NIC/TOP ST 55-805 TOP ST 55-805 TOP/TR ST 55-825 FT/TOP ST 55-829 NIC/DOLBY ST 55-839 DOLBY ST 55-839/8 DOLBY ST 55-850TOP ST 55-852 DOLBY DAVIO 55 ST 55-852 NIC/DOLBY DAVIO 55 ST 55-854 DOLBY DAVIO 55 ST 55-854/8 DOLBY DAVIO 55 ST 55-855 NIC/TOP DAVIO 55 ST 55-855 TOP DAVIO 55 ST 55-898 DOLBY ST 55-898 TOP ST 55-908 DOLBY ST 55-908/8 DOLBY ST 55-908/8 FR DOLBY ST 55-934 GB/DOLBY ST 55-998 DOLBY ST 63-255 IDTV/LOG ST 63-255/8 IDTV/LOG ST 63-270/8 IDTV ST 63-400/4 DOLBY XENTIA 63 ST 63-700 DPL/NIC/FT ST 63-700 NIC/FT ST 63-700 NIC/TEXT ST 63-700 NIC/TOP ST 63-700 TEXT ST 63-705 NIC/TEXT ST 63-710 NIC/TEXT ST 63-775 DPL ST 63-780 NIC/TOP ST 63-780 TEXT ST 63-875 DPL/FT ST 70-109 NIC/DOLBY ST 70-200 IDTV ST 70-2102 NIC/DOLBY ELEGANCE 70 ST 70-255 IDTV/LOG ST 70-255/8 IDTV/LOG ST 70-260-8 IDTV ST 70-270 IDTV ST 70-280 IDTV ST 70-5001 NIC/DOLBY DAVIO 70 ST 70-600 ST 70-602 NIC/TOP ST 70-700 A ST 70-700 DPL/NIC/FT ST 70-700 F ST 70-700 FA ST 70-700 NIC/FT ST 70-700 NIC/TEXT ST 70-700 NIC/TOP ST 70-700 S/GB/DOLBY ST 70-700 TEXT ST 70-702 NIC/TOP